Very nice, very clean
Where did you get your cable from?
Loving the builds. Gives me a lot of ideas!
How is everyone getting that gold keycap? Just ordered my GMMK Pro for Black Friday and I really want it for my build haha.
1 Like
It is the Gilded Keycap, a Guild Exclusive Keycap that Glorious does giveaways for every once in a while. There are usually a couple ways to try and land one, when they do a giveaway when you order a product like when the Numpad first released or sometimes you can get one by commenting on a specific post or going to a Glorious Meet-Up. Keep your eyes open for the next giveaway, when there is one @Millions will post the rules of entry and then itâs just a waiting game to see if you are selected to receive one
Good luck
3 Likes
Amazing looking board! 
1 Like
WOW o_o very clean !
1 Like
I see, thank you!
1 Like
No problem
Love the mousepad and keycaps color matching!! Great looking setup!!
4 Likes
Hey Hey!
First time posting, but here are my GMMK Pros. They each have been through a few configurations but these are their current setup.
Top left - My first GMMK Pro & first DIY board
Switches: KTT Kang Whites
- Lubed and filmed with Krytox 205g0, & Krytox GPL 105 on Springs
Plate: FR4 plate by AVX Works
Bottom Case: GMMK PRO FLEXKIT - G-Foam Bottom Case Foam (2 mm)
- G-Foam Plate Foam (3.5 mm)
- Soft Poron Gasket Strips
Keycaps: AKKO âMidnightâ Keycaps
Stabilizers: Durock V2 Screw-in (holee-modded) - Housing lubed with Krytox 205g0, & Wires lubed with Dielectric Grease
Other mods: Poron Stabilizer film, Pe Foam, and Tape mod
Top right - My second GMMK Pro (daily driver for my school & work system)
Switches: Tangerine (dark green stem)
- Lubed and filmed with Krytox 205g0, & Krytox GPL 105 on Springs
Plate: Polycarbonate - StupidFish Designâs GMMK Pro case and plate foam (3mm)
Keycaps: Doubleshot ABS Olivia Clones
Stabilizers: C3 Equalz V3 (holee-modded) - Housing lubed with Krytox 205g0, & Wires lubed with Dielectric Grease
Other mods: C3 Equalz Stabilizer film, Pe Foam, and Tape mod
Bottom middle - My third (Got lucky with one of the BFCM doorbuster deal)
Switches: Gateron Ink Black V2
- Lubed and filmed with Krytox 205g0, & Krytox GPL 105 on Springs
Plate: Polycarbonate
Bottom Case: GMMK PRO FLEXKIT - G-Foam Bottom Case Foam (2 mm)
- G-Foam Plate Foam (3.5 mm)
- Soft Poron Gasket Strips
Keycaps: Drop DCX âHyperfuseâ
Stabilizers: C3 Equalz V3 (holee-modded) - Housing lubed with Krytox 205g0, & Wires lubed with Dielectric Grease
Other mods: C3 Equalz Stabilizer film, Pe Foam, and Tape mod
10 Likes
Just put Cream Sodas into my GMMK Pro. Here is a sound test:
This sub $200 board holds up quite well against my Aero75 with a nearly identical setup.
6 Likes
Welcome to the group!!! I really like your pros. Makes me want to bust out my pro and actually mod that bad boy up. One day, Iâll get around to it.
1 Like
The black inks are wild. Very nice switch. And amazing selection! I was super tempted by the Black Friday deals but restrained my impulses. Only slightly regretting it.
1 Like
I recently purchase the POM plate from Green Door Geeks and wanted to try it out. What do you guys think:
7 Likes
That sounds fantastic! Beautiful build. Now Iâm questioning if I should change out platesâŚ
1 Like
The 3rd party plates are pretty darn good. This POM plate is probably my favorite of all the plates that are available. It has a deep sound like the PC plate but it fits better and doesnât have the issues of being in constant contact with the stabilizers. This causes the modifiers and the spacebar to sound different.
2 Likes
Here is an example of the POM plate in use with the Banana Splits. This is probably close to the pinnacle of what the GMMK Pro can sound like when it comes to the quintessential thocky/marbly sound.
5 Likes
Sounds amazing 
3 Likes
Well now Iâm questioning all of my decisions up until now. That is the cream cheese frosting of sound. Beautiful
3 Likes
